Fleetrun
Hecterra
NimBus
Other apps
Wialon for Android/iOS
Logistics
Wialon Local
Wialon Hosting
WiaTag
Configurator
LeaseControl
en
Contents
Eco Driving
  • tables
  • eco_driving

The report provides you with information on how a driver handles the entrusted vehicle. Analysis of the driving behavior can help you extend the life of the vehicle, reduce fuel costs, ensure cargo safety and also understand the reason for any case of emergency.

Before generating the Eco driving report it is necessary to indicate settings on the same-name tab of the unit properties dialog. Eco driving analysis is based on the data received during the trip.

The table may include the information described below.

ColumnDescription
Violation

The name of the criterion configured on the Eco driving tab in the unit properties. When you use grouping, violations with the same name will be merged into one group.

BeginningThe time when violation began. When using grouping or adding the Total row, the column shows the beginning of the trip interval, but not the beginning of the violation. If the option Show all trips is enabled, the beginning of the trip is also shown in the trip rows.
Initial locationThe address of the unit's location at the moment of violation beginning. If the option Show all trips is enabled, the end of the trip is also shown in the trip rows.
EndThe end time of the violation. When using grouping or adding the Total row, the column shows the end of the trip interval, but not the end of the violation.
Final locationThe address where the unit was located at the moment of the end of the violation interval.
ValueThe parameter value during the violation.
Avg speedThe average speed during the trip.
Max speedThe maximum speed during the violation. If no violations are detected on the trip intervals, the maximum speed value is equal to zero.
PenaltyThe penalty value indicated on the Eco driving tab of the unit properties.
RankThe penalty points converted to a 10-point rating system (can be useful if grouping by years, months, weeks, days, shifts, or trips has been applied).
Rating by violations

The individual index number of a unit/driver calculated on the basis of the committed violations. The lower the rating, the fewer violations are committed.

The Rating by violations column can be used in the report on unit groups and driver groups only.

Duration

The column shows the duration of each trip in the trip rows if the Show all trips option is enabled.

For grouping by violation and Total rows, the column shows the duration of all trips including the trips without violations. For the other grouping types, it shows the duration of the trips related to the interval of grouping, including the trips without violations.

Mileage

The column shows the mileage of each trip in the trip rows if the Show all trips option is enabled.

For grouping by violation and Total rows, the column shows the mileage of all trips including the trips without violations. For the other grouping types, it shows the mileage of the trips related to the interval of grouping, including the trips without violations.

Mileage (adjusted)The mileage for the trip taking into account the coefficient set in the unit properties (the Advanced tab).
Violation durationThe duration of the violation or grouping interval. If the violation is detected by one message, the cell shows «00:00».
Violation mileageThe mileage in the violation or grouping interval.
Initial mileageThe mileage counter value at the beginning of the trip. If the mileage parameter was not saved within the report interval, the mileage is counted from zero.
Final mileageThe mileage counter value at the end of the trip.
CountThe number of violations of this type.
Avg value of custom sensor

The average value of the custom sensor registered during the violation.

This and the following columns of custom sensor values show 0 if the value is invalid. For example, if the value is not within the bounds set in the calculation table.
Min value of custom sensorThe minimum value of the custom sensor registered during the violation.
Max value of custom sensorThe maximum value of the custom sensor registered during the violation.
Initial value of custom sensorThe value of the custom sensor at the beginning of the violation interval.
Final value of custom sensorThe value of the custom sensor at the end of the violation interval.
DriverThe name of the driver on this vehicle.
Video

Files saved during the violation interval using the Video module. To watch them, click on the icon (the number of grouped files is indicated to the right of it, if several). If several grouped files are available, you can select the required one in the drop-down list in the upper-left corner.

The column is available if the Video monitoring service is activated in the account properties. 

ImageThe images received from the unit. Viewing images in reports and the functions available while doing this are described here.

If the Rating by violations column is included in the table, then units/drivers can be placed in the table according to the violations committed (from the lower rating to the highest one). To do this, select the total grouping by rating in the parameters of the report template. The violations rating is calculated by the system on the basis of the eco driving ranks. In case the ranks are similar, the system takes the covered mileage into account. The higher the mileage value with the same rating, the lower the rating by violations is. Note that the system supports the visual marking of the rating fields according to the eco driving rank. To do this, select the colours and the values matching them in the corresponding block of the report template parameters.

Note that it is easier to analyze the received report if the grouping option was applied to the report template. The information received in the report can be grouped on the basis of different criteria, such as time (year, month, week, day, shift), type of violation and trips.

Moreover, in addition to grouping, an option of detalization can be applied. This option allows viewing the final level of nesting (date and time) inside of grouping. However, take into consideration that a penalty and rank can be given for a violation that occurred at a certain time interval (not immediately). That is why on the final level of nesting (date and time) a dash is given in the Rank column, and the Penalty column receives the value indicated on the Eco driving tab of the unit properties.

To display not only violations but all tips, activate the Show all trips option in the Additional parameters block of the Interval filtration section in the table settings.

Penalty scoring system

For each criterion, you can specify penalty points which should be credited for violations. Enter the number of points in the Penalty field on the Eco driving tab of the unit properties. The specified points are used when calculating values in the Penalties and Rank columns in the report. The main peculiarities of the algorithm used for calculating these values in the reports without grouping and with grouping can be found below.

Without grouping

If you don't use averaging, the penalty value (earlier specified on the Eco driving tab) is displayed next to every violation in the Penalty column of the report. The Total row for this column (if available) contains the sum of points for all violations.

If you use averaging (by mileage or by time), the Penalties column next to every violation also contains the penalty value that you have specified. The Total row for this column contains the sum of points for all violations divided by the number of minutes (averaging by time) or by the number of kilometers (averaging by mileage) in all trips in the report interval (including trips without violations).

With grouping

If you don’t use averaging, the sum of points for all violations in the group is shown for each parameter group in the Penalties column. The Total row contains the sum of points for all violations.

If you use averaging (by time or mileage), it is applied to each parameter group in the report table. In addition, if the report has the Total row, averaging is also applied to the total number of points earned. The averaging algorithm is described above.

Penalty-rank conversion

The Rank column of the report contains the value calculated on the basis of the received penalty points. It is a score from one to ten. 

The following function is used for conversion:
, where

x — number of penalty points,

y — final rank.


Because a six-point system was previously used, the tables below show how the rank is calculated according to the new and old systems.

New ten-point system

PenaltyRank

0

10,0

0–17

9,0–10,0

17–388,0–9,0
38–677,0–8,0
67–1076,0–7,0
107–1675,0–6,0
167–2674,0–5,0
267–4673,0–4,0
467–10672,0–3,0
more than 10671,0–2,0
Previous six-point system
PenaltyRank

0

6.0

less than 20

5.9

20–50

5.0–5.9

50–100

4.0–5.0

100–200

3.0–4.0

200–500

2.0–3.0

500–2000

1,0–2,0

Questions and answers

  Reports show incorrect mileage. What should I do?

Possible explanations and actions:

1. Outliers of data.

To detect such outliers, build a track of unit movement for the appropriate period. Outliers of data will be seen on the track as dashed lines.

Ways to overcome outliers:

  • Enable filtration of unit positional information in messages (on the Advanced tab of unit properties). This will not affect old messages but applied to new ones.
  • To correct data in reports, change settings of trip detection, in particular, reduce Maximum interval between messages and increase Minimum satellites.

2. Incorrect settings or operation of the mileage counter.

  • Check the mileage counter settings on the General tab of unit properties.

  Do reports display the data on the manual assignment of the driver after the data storage period expires?

Yes, but only if the driver has not had other assignments since they were last assigned to the unit.

If you find a mistake in the text, please select it and press Ctrl+Enter.
Thank you for your feedback!
Report a mistake
Text with the mistake Comment
Maximum 500 characters